Start here

Auditor Field Guide

A plain-language walkthrough of an entire job — before the visit, the day on site, and after you leave — so a new person with a laptop and a phone can run it start to finish.

Overview Before the visit Day of After the visit Risk ratings Writing findings Photos What not to do When to call Darren

Start here

This guide walks a new auditor through one job, from booking to invoice, using a laptop and a phone. Follow it in order the first few times. After that, keep it bookmarked for the scripts, risk examples, and the “what not to do” list.

If you are unsure about a serious hazard, a client asks for a legal opinion, someone is hurt, or a regulator arrives while you are on site, stop and call Darren at 435-901-9601.

The job in one page

Before the visit

1. Quote, agreement, and a job in the app

Use: Paperwork → Quote / Proposal, then Service Agreement. App → Start an Audit → New audit job → Step 1 Job info.

2. Send the pre-visit pack

Use: Pre-Visit Pack (email + document checklist). App Step 2 Pre-audit — check “Document request sent.”

3. Confirm access, PPE, and photos

Use: App Step 2, “Site rules & PPE.” Also the What to Bring list.

4. Charge the phone, load the app, test offline

Use: This website, opened once on Wi-Fi or good cell service.

  1. Open the site and add it to your Home Screen (iPhone: Share → Add to Home Screen; Android: menu → Install app or Add to Home screen).
  2. Open Start an Audit and confirm your job is there.
  3. Turn on airplane mode, reopen the app from the Home Screen, and confirm the job still opens. Turn airplane mode off again.
  4. Pack a charged power bank. Jobsite signal is often poor; you need the battery more than you need the network once the site is cached.

Everything you type stays on the device. After the job, use Backup / restore on the app home screen and download a backup file. Do this before you clear the browser or switch phones.

Day of the visit

Times below are a typical one-site day. Adjust if the site is large, has more than one shift, or is a long drive.

WhenWhat you doWhere in the kit
10–15 min earlyArrive, check in, orientation, put on required PPEWhat to Bring list
~15 minOpening meetingOpening script · App Step 3
30–60 minPaperwork and records review firstApp Step 6 Records · Pre-visit checklist
2–4 hrsSite walkthrough with photosApp Step 4 · Field checklist (optional printout)
During or after the walk5–10 short, private interviewsApp Step 5
~20–30 min, before you leaveClosing meeting and signaturesClosing script · App Step 7

Arrive, check in, orientation

Opening meeting (about 15 minutes)

Use: Opening meeting script (word for word, with blanks). App Step 3 Opening.

Paperwork first (30–60 minutes) — do this before the walk

Use: App Step 6 Records (jump there after Step 3). The document checklist is also in the Pre-Visit Pack.

The app numbers Records as step 6, after the walk. On site, do it right after the opening meeting anyway. Missing or weak records tell you what to watch for on the walk — for example, no fall-protection training on file means you watch the roof crew closely.

Site walkthrough

Use: App Step 4 Walkthrough. Optional printed one-page field checklist if you want paper in your hand.

Interviews (5–10 people)

Use: App Step 5 Interviews.

Closing meeting (about 20–30 minutes)

Use: Closing meeting script. App Step 7 Closing.

After the visit

Finish the report

Use: App Step 8 Report. Or the Word template in Paperwork if you must work outside the app.

  • The app builds the report from your field entries. Findings sort by risk. Photos and the action plan come with them.
  • Write the executive summary last: overall condition, top risks, top three actions, and a plain overall assessment (Strong, Adequate, Needs improvement, or High risk).
  • Every finding needs a location, a standard you have checked, a risk rating, a photo or record reference, a specific fix, an owner, and a due date.
  • Tap Print / Save as PDF. Then open Backup / restore and download a backup of the job.

Send, follow up, and invoice

Use: Email the PDF. App Step 9 Follow-up. Paperwork → Invoice.

  • Send the PDF to the client contact within the agreed timeframe (for example, 10 business days). Update the job status to “Report sent.”
  • Two to five days later, call to walk through the report. Log the call in Step 9.
  • If they want help fixing items, send a new quote. Nothing new starts without a signed quote.
  • Invoice the balance with the invoice template. Payment terms are in the service agreement (net 15 unless the agreement says otherwise). The app does not bill anyone.

Rate risk the same way every time

Use these definitions on every job, including interviews and records gaps. When two ratings both seem to fit, choose the higher one and say why in the note.

RatingWhat it meansTypical due dateExamples
High A condition that could reasonably kill someone or cause a serious injury (amputation, hospitalization, blindness, a fall from height, a collapse, a strike by heavy equipment). Fix now, or before work continues in that area. Do not leave a High item as “sometime this month.” Workers on a roof with no fall protection; an unshored trench deeper than 5 feet with people in it; a missing berm at the edge of a dump point; a driver out of hours still dispatched.
Medium A condition that could cause injury or a citation, but is not an immediate life-threatening exposure if it is controlled promptly. About 30 days, sooner if it is easy to fix. Temporary power without GFCI; a fire extinguisher that has not been inspected this month; a DQ file missing an annual review; a machine guard that is in place but damaged.
Low A minor or administrative gap. It still needs to be fixed, but it is not likely to cause serious injury by itself. About 90 days. A written program that is out of date but still being followed; a training roster missing a signature; SDS sheets present but not in the same order as the chemical list; faded labels on a properly stored container.

Imminent danger is a High finding you report to the site lead immediately, before you continue the walk. You do not have authority to shut the site down. Follow the stop-work steps in “What not to do.”

Write a good finding

Every finding in the report should answer four things, in plain language:

  1. Condition — What you saw, where, and when. Be specific (“two carpenters on the west roof, south side, no anchors or harnesses, 11:20 a.m.”), not vague (“fall protection issues”).
  2. Standard — The rule that applies, with a citation you have checked (for example, 29 CFR 1926.501(b)(1)). If you are not sure of the section, write the requirement in words and flag it to verify before you send the report. Do not invent a citation.
  3. Risk — High, Medium, or Low, using the table above, and a short “so what” (who could get hurt and how).
  4. Fix — A specific, practical action, a person responsible, and a due date. “Improve safety” is not a fix. “Install a 5,000 lb anchor and require PFAS before any work 6 feet or more above a lower level, owned by the superintendent, before work resumes on that roof” is a fix.

Sample findings — construction

High Unprotected roof work. At 11:20 a.m. on the west roof of Building A, two carpenters were setting sheathing about 16 feet above grade with no guardrails, no safety net, and no personal fall arrest. No roof anchors were visible.

Standard: 29 CFR 1926.501(b)(1). Fix: Stop roof work until a proper fall-protection system is in place (guardrails, net, or PFAS with rated anchors). Superintendent owns this; due before work resumes on that roof.

Medium Temporary power without GFCI. The spider box serving the west side saws was plugged into a permanent receptacle with no GFCI protection. The cord showed a repaired splice wrapped in electrical tape.

Standard: 29 CFR 1926.404(b)(1); 1926.405(g)(2). Fix: Put the circuit on a GFCI (or an assured equipment grounding conductor program) and remove the damaged cord from service. Site electrician owns this; due within 7 days, and immediately for the damaged cord.

Low SDS not readily accessible on the shift. The SDS binder was locked in the job-trailer office. The afternoon crew said they would have to wait for the superintendent to return to look one up.

Standard: 29 CFR 1910.1200(g)(8), via 1926.59. Fix: Keep SDS available to employees on every shift (binder in an unlocked location or an equivalent electronic system). Superintendent owns this; due in 14 days.

Sample findings — mining and heavy equipment

High No mid-axle berm at a dump point. The south dump, about 18 feet above the lower level, had a worn berm well below mid-axle height on the haul trucks in use. Tire tracks ran to the edge.

Standard: 30 CFR 56.9300. Fix: Rebuild the berm to at least mid-axle height of the largest truck before dumping resumes. Mine / pit supervisor owns this; due immediately.

Medium Workplace exam not recorded for the shift. The operator could not produce a workplace examination record for the day shift on the day of the visit. Examiners said they walk the area but do not always write it down.

Standard: 30 CFR 56.18002. Fix: Examine the working place each shift before work begins, record adverse conditions and corrections, and keep the record. Safety lead owns this; due on the next shift and then ongoing.

Low Extinguisher monthly check not initialed. The shop extinguisher tag showed no initial for the current month. The gauge was in the green and access was clear.

Standard: 30 CFR 56.4201. Fix: Inspect extinguishers at least once a month and record it. Shop lead owns this; due in 7 days, then monthly.

Sample findings — trucking and transportation

High Driver dispatched after an hours-of-service violation. A randomly sampled ELD log showed a driver over the 14-hour window on two days last week. Dispatch records show the driver was still sent on a loaded run the following morning.

Standard: 49 CFR 395.3; 395.8. Fix: Remove the driver from service until hours are legal, review dispatch procedures, and document a corrective action. Safety / dispatch manager owns this; due immediately.

Medium Driver qualification file incomplete. One of five DQ files reviewed had no annual motor-vehicle-record review and no current medical examiner’s certificate in the file.

Standard: 49 CFR 391.51; 391.25; 391.45. Fix: Obtain the missing MVR review and medical certificate before the driver is dispatched again; audit the rest of the files. Safety manager owns this; due in 7 days for this driver, 30 days for the file audit.

Low Annual vehicle inspection report not on the unit. Unit 214’s shop file had a current annual inspection, but a copy was not on the vehicle as required.

Standard: 49 CFR 396.17; 396.21. Fix: Place a copy of the annual inspection report on the vehicle. Shop lead owns this; due in 7 days, then check the rest of the fleet within 30 days.

A complete, filled-out construction report is in the sample audit. It is clearly marked SAMPLE and uses a fictional company.

Photo tips

What not to do

  1. Do not give legal opinions. You can point to a regulation and describe a condition. You cannot tell a client “you will be fined,” “you are in violation and will lose this case,” or “you should fire this person.” If they ask for legal advice, tell them to talk to their attorney, and call Darren if you are in a tight spot.
  2. Do not stop work yourself unless there is imminent danger — and even then, you do not shut the site down. You do not direct the client’s employees. If you see a condition that could kill or seriously injure someone right now, follow the stop-work steps below.
  3. Do not sign client documents (contractor agreements, waivers, indemnities, safety stand-down sheets that make you responsible for the site, or anything you do not understand). Send it to Darren first.
  4. Do not go into areas you are not trained, equipped, or authorized to enter.
  5. Do not guarantee compliance or the outcome of an inspection, citation, or claim. The audit is advisory. The client remains responsible for its program and for fixing hazards.
  6. Do not invent a citation or a credential. If you are not sure of the section number, write the requirement in words and verify it before the report goes out.

If you see imminent danger — stop-work steps

  1. Get yourself out of the danger if you are in it.
  2. Tell the site representative immediately, in plain language, what you saw and who is exposed. Ask them to remove people from the danger.
  3. You do not have authority to shut the site down or to order the client’s employees to stop. The client does. Your job is to report it clearly and now.
  4. Write down the time, the location, what you saw, and the name of the person you told.
  5. Call Darren at 435-901-9601.
  6. Do not continue the walk in that area until the client has controlled the condition. You may continue in other areas if it is safe and the site lead agrees.
  7. Record it as a High finding in the app and cover it again in the closing meeting.

When to call Darren (435-901-9601)

Call. Do not guess.

Call 435-901-9601

Which file to use

WhenOpen this
You are new, or it is the morning of a jobThis Field Guide, plus What to Bring
You need to sell or schedule the workQuote, Service Agreement
A few days before the visitPre-Visit Pack (email + document checklist)
Opening or closing meetingMeeting scripts · App Steps 3 and 7
On the site walkApp Step 4 · optional field checklist in Paperwork
You want to see what a finished report looks likeSample audit (fictional)
A toolbox talk, JSA, incident, or other formForms library (or Forms inside a job)
The job is doneApp Step 8 Report (PDF) · Paperwork → Invoice · Backup in the app
You are stuckCall Darren at 435-901-9601 · Help & contact